CONTROL PANEL BOARD

Approx. 65,000 / Piece Get Latest Price

Product Brochure
APFC Panel has microcontroller based programmable controller which switches the capacitor banks of suitable capacity automatically in multiple stages by directly reading the reactive load (RKVA) which works in the principle of VAR sensing tends to maintain the PF to 0.99 Lag. The capacitor banks may be selected in number of stages as 4/6/8 according to the load pattern. Modern power networks consists of wide variety of electrical and power electronics loads, in case of such varying loads, the power factor also varies as a function of the load requirements .So it is practically difficult to maintain consistent power factor by the use of fixed compensation i.e. fixed capacitors which shall need to be manually switched to suit the variations of the load. It can lead to situations where the installation can have a low power factor leading to higher demand charges and levy of power factor penalties. In addition to not being able to achieve the desired power factor it is also possible that the use of fixed compensation can also result in leading power factor under certain load conditions. This is also unhealthy for the installation as it can result in over voltages, saturation of transformers, maloperation of diesel generating sets, penalties by electricity supply authorities etc. It is therefore necessary to automatically vary, without manual intervention, the compensation to suit the load requirements. This is achieved by using on Automatic Power Factor Correction (APFC) system which can ensure consistently high power factor without any manual intervention. In addition, the occurrence of leading power factor will be prevented.APFC products are fully automatic in operation and can be used to achieve, consistently high power factor under fluctuating load conditions Reduced KVA demand charges, Lower energy consumption in the installation by reducing losses Preventive leading power factor in an installation.

Install APFC Panel to avoid penalties and enjoy the benefits automatically. For maintaining the power factor according to the load factor, proper capacity of capacitors is to be connected. The value of capacitors to be connected will vary with respect to load and its existing PF. There are two ways to maintain PF-
Fixing of capacitor at the load end permanently or at the mains. Generally which is recommended for the fixed load like pumps, fans etc. and it is not possible for the load which has variations in the load and PF.

The power factor can be maintained by installing Automatic Power Factor Control Panel (APFC Panel)

Approx. 75,000 / Piece Get Latest Price

Product Brochure

We also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.
Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks.
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV.

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions.
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

We offer the Best LT Panels,To Get the Best Prices for LT Panel,you can contact us.

Approx. 86,000 / Piece Get Latest Price

Product Brochure

PCC Panels are the most essential part of electrical system of an industry from where the power of the industry is controlled. Perfect Products (India) is widely known for premium quality PCC panels designed and manufactured according to the customer specifications. Best quality switchgear and busbar are used for reliable and efficient performance.

We manufacture PCC panels with rated current ranging from 630A to 6300A

PCC panels are manufactured in a perfectly compartmentalized structure.

Premium quality insulators are used to ensure safety.

There can be a provision of space heater, thermostat and backup protection if required by customer.

User friendly, safe and reliable

We offer best PCC Panels,To get them at Best Prices,you can contact us.

Approx. 1.25 Lakh / Piece Get Latest Price

Product Brochure

Beta power known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming. 

Control panel consist of a controller. Controller may be PLC, DCS, relay or some other type. It gives digital signal input signal to the MCC panel to start the motor. Control panel works based on the PLC /DCS program or the relay logic. Instruments are normally connected to control panel. Indications for the interlocks also will be there in control panel. Nowadays single panel is used of using separate control and MCC panel. 

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay based systems. Control Systems Engineers has provided PLC based Panels from PLC of Allen Bradley, Siemens, Modicon, GE Fanuc. From small I/O application to the complex I/O systems are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.

Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks. 
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV. 

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. 
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 95,000 / Piece Get Latest Price

Building projects requires MV Distribution Panel Boards for distribution of power to each utilities. A good electrical distribution network will have proper design, right components, and future load provisions. Space utilization will also be an important factor for maintenance and handling of the equipment. Here we look into what are the features required for design, manufacture, install a MV Distribution panel board including its BIS (IS) standards that serving quality building projects.

Approx. 85,000 / Number Get Latest Price

Product Brochure

Beta power known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming. 

Control panel consist of a controller. Controller may be PLC, DCS, relay or some other type. It gives digital signal input signal to the MCC panel to start the motor. Control panel works based on the PLC /DCS program or the relay logic. Instruments are normally connected to control panel. Indications for the interlocks also will be there in control panel. Nowadays single panel is used of using separate control and MCC panel. 

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay based systems. Control Systems Engineers has provided PLC based Panels from PLC of Allen Bradley, Siemens, Modicon, GE Fanuc. From small I/O application to the complex I/O systems are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.

Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks. 
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV. 

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. 
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 1.45 Lakh / Number Get Latest Price

Product Brochure

Beta power known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming.

Control panel consist of a controller. Controller may be PLC, DCS, relay or some other type. It gives digital signal input signal to the MCC panel to start the motor. Control panel works based on the PLC /DCS program or the relay logic. Instruments are normally connected to control panel. Indications for the interlocks also will be there in control panel. Nowadays single panel is used of using separate control and MCC panel.

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay based systems. Control Systems Engineers has provided PLC based Panels from PLC of Allen Bradley, Siemens, Modicon, GE Fanuc. From small I/O application to the complex I/O systems are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.

Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks.
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV.

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions.
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 1.45 Lakh / Piece Get Latest Price

Product Brochure

a fire panel is a safety appliance that commercial buildings typically require in order to set into motion a number of tasks that could save lives and minimize property damage. If you’re in charge of ensuring a building has all the required features necessary for the sake of safety, you might be in the market for a fire panel. Before you start looking for one, you should get to know what the typical fire panel does, which buildings need one and which features to look for in a fire panel.

why do you need a fire panel in your building?

the point of a fire alarm control panel is to activate a quick emergency response when there’s a fire so everyone in the building has a chance to get out safely. Different fire panels on the market have different features, so the capabilities of this product can vary. For example, a basic fire panel might sound an alarm to alert everyone of the danger. Some fire panels also call the fire department, and some even activate the building’s sprinkler system to try to put the fire out fast. The capabilities depend on which fire panel you decide to buy.

if you’re wondering how the fire panel works in general, note that when a fire breaks out, the fire panel receives a signal from smoke detectors, the fire sprinkler system, a manual call point or a pull switch in the building. This means it can’t detect the fire on its own, but it can respond to the signals it gets from the systems that detect the smoke. At that point, the fire panel’s response is activated, which might include making a loud noise and lighting up to warn people of the fire, and then it may send a signal to the fire department or alarm company to get emergency crews to rush to the building and put out the flames.

main types of fire panels

there are two main types of fire panels available. Conventional panels have been around for years, so you might see them in older buildings. They work by responding to changes in an electrical current, such as when a smoke detector identifies smoke and changes the current in response. Once the fire panel detects this current, it sounds the alarm. The conventional fire panel is installed in different zones—such as the first floor, second floor, etc. —so it’s often also called a zoned panel.

the newer type of fire panel is called an addressable panel. This system runs off modern technology, since it features a microprocessor that sends data from devices in the building to the panel, rather than just sensing changes in electrical currents. Every device in the building’s fire detection system has its own address, so the addressable fire panel can identify which device the signal is coming from. This makes it easy to locate the device that has sent signals to the fire panel.

which buildings need a fire panel?

most buildings require a fire panel, but if you’re not sure if yours does, you can check documents from the national fire protection association (nfpa) or the international building code (ibc) to find out. For example, you can read nfpa 101: life safety code, or you can reference documents that discuss international building code. The specific requirements may vary based on the type of business that’s in the building and its occupancy, but generally you can expect to need a fire panel as part of your overall fire alarm system.

Approx. 75,000 / Piece Get Latest Price

Product Brochure
Automatic Star / Delta Starter with Timer for 3-Phase AC Motors

In this tutorial, we will show the Star-Delta (Y-Δ) 3-phase induction AC Motor Starting Method by Automatic star-delta starter with Timer with schematic, power, control and wiring diagram as well as how star-delta starter works and their applications with advantages and disadvantages.

Table of Contents 

• Automatic Star Delta Starter with Timer Wiring & Installation Diagram
• Operation & Working of Automatic Star Delta Starter
• Star Delta Starter Power Diagram
• Control Diagram of Star Delta Starter with Timer
• Wiring Diagram of Star Delta Starter with Timer
• Advantages & Disadvantages of Star Delta Starter with Timer
• Characteristics & Features of Star-Delta Starter
• Applications of Star Delta Starter

Explanation of the working and operation of Star Delta Automatic Starter with Timer Wiring Installation:

From the left you have the main contactor with the pneumatic timer because your main contactor is always energized, in the Middle you have the Delta contactor with a thermal overload for motor protection in case the motor exceeds the ampere rating set on the thermal overload, on the right you have the Star contactor which is the first contactor to be energized with the main contactor then when the timer reaches its time limit the Star contactor de-energizes and the Delta contactor energizes and the Motor is running at full load.

Approx. 4.45 Lakh / Piece Get Latest Price

Product Brochure

We also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.
Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks.
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV.

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions.
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 69,999 / Piece Get Latest Price

Product Brochure
MCC stands for motor control center. It consists of feeders for motors and blowers. Feeders are designed according to the motor rating. In most of the MCCs, auto/manual provision will be there. With manual provision motors can be operated manually. In auto provision external signal is required to start the motor. The signal is given by the control panel. Indicators for the motor operation also will be present in control panel.
A motor control center (MCC) is an assembly of one or more enclosed sections having a common power bus and principally containing motor control units. Motor control centers are in modern practice a factory assembly of several motor starters. A motor control center can include variable frequency drives, programmable controllers, and metering and may also be the electrical service entrance for the building.

To get the best prices for our MCC Panels,contact us.

Approx. 95,000 / Number Get Latest Price

Product Brochure

Beta power known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming. 

Control panel consist of a controller. Controller may be PLC, DCS, relay or some other type. It gives digital signal input signal to the MCC panel to start the motor. Control panel works based on the PLC /DCS program or the relay logic. Instruments are normally connected to control panel. Indications for the interlocks also will be there in control panel. Nowadays single panel is used of using separate control and MCC panel. 

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay based systems. Control Systems Engineers has provided PLC based Panels from PLC of Allen Bradley, Siemens, Modicon, GE Fanuc. From small I/O application to the complex I/O systems are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.

Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks. 
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV. 

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. 
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 1.25 Lakh / Number Get Latest Price

Product Brochure
VFD Control PanelWhat is VFD Panel?
Beta power Variable frequency drive control panel (also named VFD panel, AC drive electrical control panel) is consisted of inner VFD inside the cabinet with external control, protect, display and other electrical, it's an frequency conversion device to control three phase AC motor (including fans and pumps) in variable speed to save energy.

VFD panels adopt enclosed cabinet structure, generally, the protection class is IP20, IP21, IP30, and some panels may reach IP64, IP65 and even IP66 where the application environments need weatherproof, waterproof. The panels surface are coating spray by suppliers, and easy to install in parallel, the panel top configure bus and wiring the VFD keypad to the panel's door for operating directly.

Variable speed drive is a dedicated component of the electrical control panel, the panel's frequency convention and main features are depending on the inner VFD and other components configuration. VFD panels are different according to their different functions and applications, generally, it needs customized manufacture base on specified running environment, like in constant water supply panels (one panel control 1, 2, 3 pumps, etc.), escalators control panels, central air condition circulating pump panels, and fan's control panels.

Why we use VFD Panels?

1, Power switching and protection
VFD panels are designed with a circuit breaker usually, which are connected to the input line power supply to switch the panel on/off, and provide protection when short circuit or overload occurs in the circuits and variable speed drives. In addition, VFD panels can disconnect power to ensure operator's safety during motor maintenance.

2, Adjustable speed
A frequency control potentiometer is installed on the VFD panel's door, to transmit command signals to the motor according to operator assigned. VFD panel has mains switching function to ensure the system continues operation in case of the variable frequency drive failed.

3, Visual control
VFD panel has display and operation panel on the front body, which is connected to the electrical components inside the control cabinet. It can display the panel's operational status visually, and convenient for operator control the motor in actual field operations.
Manufacturers also equip with a variety of instruments and indicators inside the variable frequency drive panels, such as voltmeter, ammeter, frequency meter, and power indicator light, alarm lights, running lights, power frequency lights etc, which will monitor the VFD control panels working status in real time.

4, Security protection
Include variable frequency drive, all other electrical components are integrated inside the VFD panel, thus reducing the impact of external environment to the electrical components, and ensure the operator safety level like reducing shock hazard rate, so it has a better safety protection function.

Typical applications: water supply, air compressors, central air conditioning, port machinery, machine tools, boilers, paper machinery, food machinery and so on.

Approx. 2.45 Lakh / Number Get Latest Price

Product Brochure
LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks. Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV. 
Main Features :
Design and conceptualization based on Client design and specificationsPreparation of bill of quantities, tenderingPreparation of detailed drawings, site set outSourcing of material from different well known vendorsEvaluation and submission of progress reportExecution of planting schemesTotal commissioning as per the request of our esteemed clientAs per client request we do testing of Panels, repairing and replacing the panels which are not in good condition
LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. Our LT panels are designed to work with low electricity consumption that makes them cost effective
HT Panel is like LT Panel except that it is used for high tension cables.

Approx. 1.15 Lakh / Number Get Latest Price

Product Brochure

Beta power known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming. 

Control panel consist of a controller. Controller may be PLC, DCS, relay or some other type. It gives digital signal input signal to the MCC panel to start the motor. Control panel works based on the PLC /DCS program or the relay logic. Instruments are normally connected to control panel. Indications for the interlocks also will be there in control panel. Nowadays single panel is used of using separate control and MCC panel. 

Ease in modification of logic, reduced size, means of remote communications and advances in the technology have made PLC Automation Control Panels an edge over conventional relay based systems. Control Systems Engineers has provided PLC based Panels from PLC of Allen Bradley, Siemens, Modicon, GE Fanuc. From small I/O application to the complex I/O systems are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMI/MMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.

LT PANELSWe also provide service in cable laying services. We offer install, testing and commissioning of HT & LT cables in trenches, trays and pipes.

Cable laying services in industrial complexes, or over large distances, they are staffed by our expert technicians and engineers who perform cable preparation, jointing, termination, testing, commissioning, maintenance and troubleshooting tasks. 
Cable laying services differ in terms of capabilities like may require cable laying services for low voltage (LV), medium voltage (MV) or higher voltage (HV) cables up to 33 KV. 

Main Features :

Design and conceptualization based on Client design and specifications

Preparation of bill of quantities, tendering

Preparation of detailed drawings, site set out

Sourcing of material from different well known vendors

Evaluation and submission of progress report

Execution of planting schemes

Total commissioning as per the request of our esteemed client

As per client request we do testing of Panels, repairing and replacing the panels which are not in good condition

LT Panel is an electrical distribution board that receives power from generator or transformer and distributes the same to various electronic devices and distribution boards. Such panels are used in industries both for internal and external use and, therefore, they are quite rugged to withstand different climatic conditions. 
Our LT panels are designed to work with low electricity consumption that makes them cost effective

HT Panel is like LT Panel except that it is used for high tension cables.